LGB G Scale LED Tiffany Opal Lamp Fixture - Low Profile peel and stick 3M mount

Description

G Scale LED Tiffany Opal Lamp Fixture - Low Profile peel and stick 3M mount
- 18 inch micro black wires - requires an SL LED controller
Ready to run;
pre-wired - ready to run with an optional SL LED controller
Shourt Line Product Number: No.
SL-8291230
pre-wired ready to install
Mount to any loco, car or building ceiling in seconds
Direct From Manufacturer-
Made in the USA
Mounts on any loco or car ceiling, perfect for exterior or interior lighting
.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
Google
SL 8291230
for more product details and larger photos
Buy it now Price:

.59
New
Description:
For indoor or outdoor use
This new, easy to use Tiffany style white opal lamp fixture uses a high intensity warm white LED. This is the second series of G scale prototypical light fixtures available from the Shourt Line. The first used simulated oil lamp fixtures. This one spans the gap between gas and electric illumination. It has a Tiffany style opal lamp shade for period design and a special mounting base with a low profile so it can be used with LGB doors on exteriors of cars and also gives maximum head room inside cars.
This 1 LED fixture does require the use of a Shourt Line LED controller dimmer for safe and efficient operation and works without the use of dropping resistors or complicated formulas. The SL LED controllers are available with solder and screw type terminals for in car wall and ceiling mounts as well as under car mounting on any G scale short or long cars.
The SL LED controller is up to 94% efficient so that even the LGB starter set power pack will power a loco, its lights and 12 LED lamps plus additional car lighting for future expansion. The newest SL LED controller is unique in operating at 1/6th the power of any other available and it also works at the lowest track voltage or no track voltage, it fact it operates 8 LEDs up to 5 minutes without any track power!
F
eatures:
SL-8291230
High Output
Warm White LED color for matching bulb color temperature
Warm Warm White (WWW) and Yellow Warm White (YWW) color also available on request.
Opal Lamp shade for diffused lighting
Prototypical Appearance
Low Profile height permits LGB doors to open and close
Square black mounting plate with 3M adhesive
Peel and Stick Installation
Dimensions:
Fixture height:
8mm (.33")
Fixture diameter:
16mm (1.1")
Fixture mounting pad dimensions: (12mm (.6") square
Wire: 2 each 30 AWG solid copper plated with black jacket each 18 inches long
Default color temperature is Warm White which is matched for 3,200 degrees Kelvin that matches LGB two pin bulbs in color temperature. Use the Incandescent setting on your camera from proper color temperature in your photos.
At the time of order you can request the Yellow Warm White or the Warm Warm White but we recommend using the Warm White standard unless you want to simulate a yellow outdoor bug light (YWW) or candle flame (WWW) see the photos below to compare.
You will receive the recommended Warm White LED lamp fixture shown on the right side of the photo above unless you request the WWW or the YWW color temperature LEDS with your order.
This photo shown the right angle SL 1 LED Tiffany style Opal Lamp fixture with simulated wood mounting bracket. Note the difference in color temperature in the pools of light from each fixture. The Warm White is recommended but the other color temperatures are available upon request.
(The right angle fixtures above are not included with this item but available at our store)
Instructions:
The photos shown below are for examples of use, wiring and placement. Only a single Tiffany style Opal LED fixture, pre wired with 18 inch leads, come with this item.
This item requires an SL LED controller for safe and efficient operation. We install lighting products an all makes of G scale cars if you do not want to do it yourself. SL LED controllers area available in both solder and screw terminal types. We will set up the controller of your choice when requested so you do not have to adjust the voltage per the instructions that comes with each controller. A volt/amp meter is required to set the safe operating voltage on our SL LED controllers. Other makes and models of controllers may not work with direct parallel wiring of LEDs. If you want to use another controller be sure to use dropping resistors on each LED as they usually will not provide proper operation without them. All our controller work without dropping resistors.
Adjust your SL Lighting controller using the instructions provided with your controller
Do not use a voltage above 3.1 volts
Test the fixture
by connecting the long stripped wire to + and the shorter stripped wire to - output of a Shour Line LED controller that has been previously set to the proper voltage
Check to see the lamp turn on, if not reverse the leads and retest - mark the + and - leads of the lamp for later wiring to the controller
If the lamps fails to light contract us at the ShourtLine.com
Clean the surface
where you want to mount the fixture with an alcohol wipe
Peel off the read tape to reveal the 3M adhesive pad
Hold the fixture above the mounting surface to check the correct position
before it touches the mounting surfac
e.
Apply gentle pressure by pushing with a
finger on the LED
Route the wires to an an existing SL lighting fixture and SL LED controller or a separate SL LED Controller of your choice
Use only with an SL LED controller
; damage to your led fixture is not covered with other controllers or if instructions are not followed.
Each fixture comes with 18 inch micro cable leads for installation in any loco, car, or building. You lighting fixtures will provide a wide angle illumination as shown above.
To install, clean the surface you want to mount to with an alcohol wipe, peel off the read tape to reveal the 3M adhesive pad and apply.
The fixtures 18 inch wires allow wiring with any car. The photo above shows two fixtures mounted the exterior porch of an LGB car that also has an SL 4 Opal Lamp fixture installed.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
This photo shows 2 each
SL-8201230
opal fixtures mounted on the sloped interior ceiling for toilet illumination wired to an
SL-8208230
8 LED Opal fixture.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
This photo shows a
SL-8291230
fixture mounted to the cupola's ceiling, another
SL-8291230
fixture is mounted on the rear platform ceiling and an
SL-8101110
pre-wired LED with plug-in mount for an LGB exterior lamp.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
This photo shows 2 each
SL-8291230
1 LED Opal fixtures mounted to the exterior platforms and 2 each
SL-8101110
1 LED plug-in mount for LGB exterior lamps all wired in parallel to an
SL-8101110
5 LED Opal Caboose fixture. All the LEDs are controlled and dimmed by an
SL-8453003
Precision Train Throttle & LED controller mounted
inside the caboose and covered with an
SL-7453003
3 Side Snap On Cover . Also shown is an
SL-6111100
10KuF Anti-flicker Buffer wired to the controller and to a track power pickup at the bottom of the car.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
The Shourt Line
SL-8453003
Precision Train Throttle & LED controller shown above is used for AC, DC or DCC track power. The controller can power and dim over 300 LEDs at up to 94% efficiency from AC,DC or DCC at 4 to 35 volts. It uses 1/6 the power of all other lighting systems available.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
This photo shows a
PIKO 36167
single axle ball bearing power pickup connected to an
SL-4128510
Power Connector Cable power pickup cable that routes inside the car to provide power for lighting.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
An SL LED controller can also be mounted on the bottom of a car and powered from a loco. The
SL-6525911
lighting system provides; LED control/dimmer functions, a UPS circuit with a DC to DC changer and super capacitor bank for powering all 12 LEDs up to 3 minutes without track power, an Aux Out circuit as shown above that is wired to the exterior lamps so they automatically, slowly turn on when the train stops and go off when the train starts. The Automatic circuit has a special feature that smoothly brings the lamps to full brightness regardless of how fast the train stops.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
This photo shows the
SL-6525911
LED controller system that
provides; LED control/dimmer functions, a UPS circuit with a DC to DC changer and super capacitor bank for powering 8 LED lamps up to 5 minutes without track power, and an Aux Out circuit shown above can be wired to exterior lamps so they automatically, slowly turn on when the train stops and go off when the train starts. The
SL-6525911
LED controller
circuit has a special feature that smoothly brings the lamps to full brightness regardless of how fast the train stops.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
It is easy to wire the 1 LED lighting fixtures to any existing lighting fixture connected to an SL LED controller as ALL LEDs are wired in parallel, + to + and - to -. No dropping resistors are need or complicated formulas. Just wire + to + and - to - on existing fixtures or to any SL LED controller. Up to 300 LEDs can be powered from each SL LED controller.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
All the trains car lighting can be controller and powered from a single SL controller if desired. Use the SL 2 or 3 pin LED connector, the 3 pin version allows independent operation of exterior lights and is shown below. The connectors have a fast release feature in case of derailment so wires can not be damaged.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
Notice that the low profile fixture allows car doors to move freely. This photo shows the 3 pin connector at the front of the blue 2nd car.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
HINT: when wiring from car to car route the wires low on the car for a prototypical appearance. This view of a passenger car with bottom mounted controller is connected with LGB power plugs that match power plug on the rear of the loco.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
Notice that the 1 LED Opal Lamp fixture is wired in parallel to the existing SL 4 LED lamp fixture which in turn is wired to the all in one controller/dimmer, UPS and Aux Output that is on when the train stops.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
Photo
s:
Easy to use peel and stick single LED Tiffany style Opal Lamp Fixture.
Don't leave your passenger in the dark! Use these single LED Lamp fixtures where you need light.
(train, track figures, LED controller and 4 LED fixture not included but available at our store.
Google
SL 8291230
for more product details and larger photos
Questions? Click on link above
Thanks for looking - ShourtLine.com by Soft Works Ltd.
copyright 2020 Shourt Line - Soft Works Ltd. all rights reserved